95 RCSB to LQ4/4L60e

This 95 is a project that I'm working on for a member from another board that I'm on. It started life as a 350TBI/4L60e and I'm swapping in an LQ4/4L60e. Trans will be updated with the Gen III/IV style 4L60. Using a Nelson Performance Harness, Transdapt Adapter Plates, and everything else needed for a Smog Legal Setup. I'll go into detail with the swap and take pics along the way.

http://i35.photobucket.com/albums/d1...s/101_3290.jpg



http://i35.photobucket.com/albums/d1...s/101_3293.jpg



Getting ready to pull the engine
http://i35.photobucket.com/albums/d1...s/101_3295.jpg



Got a little help from a friend
http://i35.photobucket.com/albums/d1...s/101_3297.jpg



Me removing the last little connections
http://i35.photobucket.com/albums/d1...s/101_3299.jpg



http://i35.photobucket.com/albums/d1...s/101_3302.jpg



http://i35.photobucket.com/albums/d1...s/101_3308.jpg



http://i35.photobucket.com/albums/d1...s/101_3314.jpg



All Gone...
http://i35.photobucket.com/albums/d1...s/101_3322.jpg



http://i35.photobucket.com/albums/d1...s/101_3326.jpg

And the Degreasing Begins...
http://i35.photobucket.com/albums/d1...s/101_3323.jpg



http://i35.photobucket.com/albums/d1...s/101_3324.jpg



http://i35.photobucket.com/albums/d1...s/101_3325.jpg



A little better...
http://i35.photobucket.com/albums/d1...s/101_3329.jpg

badass man...that a SS truck?btw camaro on sig looks sick..what color is that

LQ4
http://i35.photobucket.com/albums/d1...s/101_3331.jpg



http://i35.photobucket.com/albums/d1...s/101_3332.jpg



Transdapt Mounting Plates
http://i35.photobucket.com/albums/d1...s/101_3333.jpg



Dropping it in for a test fit
http://i35.photobucket.com/albums/d1...s/101_3335.jpg



Looks Right at home
http://i35.photobucket.com/albums/d1...s/101_3336.jpg



http://i35.photobucket.com/albums/d1...s/101_3337.jpg



Put the intake on to see how it would look
http://i35.photobucket.com/albums/d1...s/101_3339.jpg



Looks like a pretty good fit...
http://i35.photobucket.com/albums/d1...s/101_3340.jpg



http://i35.photobucket.com/albums/d1...s/101_3342.jpg



http://i35.photobucket.com/albums/d1...s/101_3343.jpg



http://i35.photobucket.com/albums/d1...s/101_3344.jpg



http://i35.photobucket.com/albums/d1...s/101_3345.jpg

Quote:

---

Originally Posted by CHEVROLADE

badass man...that a SS truck?btw camaro on sig looks sick..what color is that

---

No it isn't. Thanks it's a HOK Kandy. Close to JSB from the Vette. Nice truck in your sig too!!

http://i35.photobucket.com/albums/d1...5/101_2619.jpg
http://i35.photobucket.com/albums/d1...5/101_0839.jpg

On the Transdapt Plates, it seems like the bolts that bolt the factory 350 mounts to the adapter plates are too long, have any of you ran into this problem before?

Also, Not sure which wires on the old Harness to remove and which to keep. I've searched all over. I know that the Nelson Performance Harness has a few connections that need to be hooked up but I wasn't 100% sure about those as well. If anyone can help it'd be greatly appreciated. I'm going to try to figure out the Wiring tomorrow.

Matt

all the wires for the new harness can be hooked into the leads coming from the main harness going into the firewall on the driver side firewall. I can't remember if I documented the ones I used in the "current top secret project" topic I made when doing the 93 conversion.

I had the same problem with the transdapt plates. I ground the bolts down til they fit right.

Quote:

---

Originally Posted by RedHeartbeat

all the wires for the new harness can be hooked into the leads coming from the main harness going into the firewall on the driver side firewall. I can't remember if I documented the ones I used in the "current top secret project" topic I made when doing the 93 conversion.

---

Cool thanks I'll check out your build thread

Quote:

---

Originally Posted by bstill

I had the same problem with the transdapt plates. I ground the bolts down til they fit right.

---

I figured that's what I'd have to do. Thanks

I wouldn't cut any wires until you get everything working as it should. Just zip tie them all put of the way, that way you don't accidently cut something you need. I traced the wires one at a time and pulled them out of the way