Engine | Transmission | Drive Axle | Chassis | Fuel
Finally finished the 80e conversion. Damn, I need a lift in the worst way, my shoulder blades are raw from crawling around on my back under the truck...
Transmission General Description The Hydra-matic 6-Speed RWD is a fully automatic, 6-speed, rear-wheel drive, electronic-controlled...
This is a common question on the board so here is a link to Hit Man X's post over on GMFullsize ...
Guys...YOU'RE WELCOME. :dancenana: LS General Charts Seriously...go ahead. Take a look. I personally pooped my drawers after finding this. ...
Engine swap in a 2001 Silverado '01 4.8L to '07(classic) 6.0L This is a step-by-step removal and replacement of the 4.8, 5.3 and 6.0L trucks. This...
Below is a list of terms & abbreviations common to everything vehicle related (if you need a course on chat room lingo & abbreviations, Google it!)....
This may have been posted already, but if it is, I can't find it. Anyway, below is a link to RPO codes...pretty helpful for figuring out gearing,...
Alright everyone, I figured Id make a semi short transmission install write up, hopefully this can help someone in the future. vehicle receiving...
Hey guys I was considering putting a lift kit or a leveling kit on my TB, but was first curious if anyone else has. Mainly I'd like to know if I need...
I have a 2000 silverado. Can someone please tell me what i need to do, to convert my truck from Drive by Cable, to Drive by wire (I know most ppl...
I have a 2000 LM7 in a silverado... (Really rare right? lol) I've found an 03 LQ9 and i know its a good choice cam for me, what i don't understand...
SOOO, I have owned this truck since 2007... It now has 350k miles on it and was running perfect until my fuel lines rotted out... Just put new ones...
Does anyone have one, ever seen one? What all LS engines are out there ( Liter/ HP/ Head / from what vehicle ) from the 4.8 - where are we 6.5...
I’m doing a 6.0 swap on a 2001 Silverado, donor truck from 6.0 came from a 2002 I did get the ecm and harness. MY 2001 as you may know is a drive...
Well - here is a modified set-up using Cloyes and GM Performance Parts camshaft timing components (see images). Note the REMOVAL of the small thin...
Has anyone used the OBS to LS swap long tube headers? Stainless steel and look pretty good, just curious if someone had used these before?
Hey guys is it possible to get a 6L80 truck swap over the wiring for the powertrain into a RV or am I going to require the body controller also ?
i know there ain't hardly nobody left who likes rowing their own gears nowadays... much less folks who also hop up the engines, too, but hopefully...
hi all, im new here. ive read through many of your guys forums for years. just never joined till now, anyways. I have a 2004 silverado ls long bed...
Hey guys. I have been running circle D's "off the shelf" "GM 278mm HP 4L80 LS Torque Converter" since my swap. It seemed to be fun when I was...
my headers for my build came in today, but they came with two different pairs of gaskets im not sure what set I should use, pictures below ...
Questions on the Castech #706 casting coolant leak problem? Does the leak start only after the engine has been once over heated or do they just...
I have an 04 Yukon Denali and will be attempting to swap a push button 4wd transfer case in place of my AWD system. I'm also getting a good deal on...
I've got a few questions about swapping the AWD transfer case in my 04 Yukon Denali to a push button 4wd setup and wanted to know if anyone's done...
I have a 73 c10 With a dbc 5.3 It has a 4l60e in it It has the TCC hooked up Two things first The Speedo when connect to my WiFi dongle...
Would like some help with this. The wife's 5.3 has cracked heads was going to just change out the heads but at 250k why. I have a 4.8 with 40k on it...
Hey guys Im doing a LQ4 into a 22ft winnebago RV with a 4L80. I will be using this rv to go on cross country road trips with friends and more then...
Hey guys I have a issue from trying to use my built 4l60e to my new 5.3. It feels like the torque converter is pashing against the flex plate and not...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules