All LS Based Conversions
Starting this to answer as many questions as I can in one place. I am trying to compile the most complete list of what to do to complete a conversion...
2001 silverado (Thanks Banker099) This image has been resized. Click this bar to view the full image. The original image is sized 799x247...
Hey Guys, these questions get asked quite a bit, and what better way than to make a sticky with all the part numbers you'll need. I'm open to...
I love reading these threads so i figured id start one of my own...this will be a long process i already know! So heres my truck: had...
Hey everybody! This will be my first major thread. Ive been wanting to do a swap for a long time. Didn’t know which engine I was going to use but...
Im gonna start a build page here for my 93 Silverado. I've done a lot of work on it so far just to get it lookin decent but now its time for some...
I'm going to post what I did to mate my nv3500 to my 5.3 since I wasn't able to find any reliable info when I did my swap. I bought the flywheel from...
Does anyone (or allen) do harness graftin'? I'm in need of ideas for graftin' a 5.3 engine harness into the OBS ('86) fuse block (engine...
I just finished making an A/C bracket kit that will allow the stock A/C compressor and lines to be used when doing a Gen3 install. I have seen a lot...
well things are going to be going slow on this since i'm pretty much ordering as i go and right now work is slow lol. I've been researching for a few...
Long time lurker and now I am going through with it. I recently acquired an 01 Denali at work and I am pulling the motor & trans. LQ4 4L60E...
Well, I thought I would start a build thread to document my progress. As most know, and with Kurt's help, I picked up a 1968 Chevrolet C10 step side...
So this is my build thread. Ill be starting the swap tomorrow... :ugh2: Its a 1992 K1500 Blazer. Stock 350 TBI with almost 250000 miles on it and...
anybody heard of someone doing this swap? a have an 83 ranger and i was wondering what all i would need to make it work
Well. First Post. Here goes... I hope I put this in the right section of the forums. I am building a LM7 (5.3) motor into a 383. I know this kind...
Hello guys, I am finally doing my swap that I've been talking about doing for the past 2 years LOL. First off I am working with a 1994 Silverado...
This forum has helped me a bunch for my swap. I’m about 90% done, except for a few gauges and wire cleanup. I am stuck on my fuel gauge, the...
I thought I would throw up some pics of my 5.3L/4L60E swap into my 85 GMC swb 2wd pickup. My build log is over at Glock's new project: "Fred" - The...
after a bad string of luck with motors, i put the silverado back bone stock. i was just fed up with it and needed a break. i always wanted a s10 to...
okay, since i'm starting this thread after a few weeks of tearing into her i'll combine what I have so far. I bought her as an unfinished project...
Time to do another swap, this time a 2 door Tahoe. I picked up a 5.3/4l60e combo last night for $350.00. I'm hoping I still have some extra parts...
I have. A 1994 c1500 w/t that had the old 4.3 in it. I have the 5.3 dropped I with my 4L60 behind it. The guy from LT1 swap.com already did the pcm...
I'm having trouble finding exactly what wiring is required for the modified LM7 harness to swap into a 98 sierra with a 5.7 vortec. I have followed...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules